Low vision clocks are specially designed wall or desk clocks with features such as voice activation or speaking the time, projecting the time on the wall, tactile numbers and hands, luminous dials, large numbers, and Braille digital clocks to assist low vision or blind individuals in telling the time while enhancing personal independence. NEW 7.5' Large Display: Compact size (7' x 1.5' x 3') with 2.5' tall digit. Big white bold numbers against black face creates easy read from across the room, perfect for the elderly or the sight-restricted person.
Electric Clocks
Classification
There are actually four basic design classifications:
▪ Electromechanical clocks that use mechanics to rewind the mainspring (via attachment of a motor or an electromagnet)
▪ Electromechanical clocks that use mechanics to operate the pendulum or oscillator
▪ Electromagnetic clocks that use electromagnetic impulses to operate the pendulum or oscillator
▪ Synchronous clocks that rely on the the 50 or 60 Hz utility frequency of the AC power line as a timing source, by driving the clock gears with a synchronous motor.
[edit]
History
Electric Table Clocks With Large Numbers
In 1814, Sir Francis Ronalds (1788) of London invented the forerunner of an electric clock, the electrostatic clock. His prototype was powered with a dry pile battery. It proved unreliable in timekeeping, however, because of a strong dependence on a stable room temperature and 'weather conditions'.
In 1815, Giuseppe Zamboni (1776-1846) of Verona invented and showed another electrostatic clock run with dry pile battery and an oscillating orb. Over the test of time Zamboni's clock was praised 'the most elegant and at the same time the most simple movement yet produced by the electric column'.[1] Zamboni's clock had a vertical needle supported by a pivot and was so energy efficient that it could operate on one battery for over 50 years.
Numerous people were intent on inventing the electric clock with electromechanical and electromagnetic designs around the year 1840, such as Wheatstone, Steinheil, Hipp, Breguet, and Garnier, both in Europe and America.
In 1840, Alexander Bain (1811-1877), a Scottish clock and instrument maker is the first to invent and patent the electric clock. His original electric clock patent is dated October 10, 1840. On January 11, 1841, Alexander Bain along with John Barwise, a chronometer maker, took out another important patent describing a clock in which an electromagnetic pendulum and an electric current is employed to keep the clock going instead of springs or weights. Later patents expanded on his original ideas.
Matthias Hipp (1815-1893), clockmaker born in Germany, is credited with establishing the production series, mass marketable electric clock. Hipp opened a workshop in Reutlingen, Switzerland, where he developed an electric clock to have the Hipp-Toggle, presented in Berlin at an exhibition in 1843. The Hipp-Toggle is a device attached to a pendulum or balance wheel that electromechanically allows occasional impulse or drive to the pendulum or wheel as its amplitude of swing drops below a certain level, and is so efficient that it was subsequently used in electric clocks for over a hundred years. Hipp also invented a small motor and built the chronoscope and the registering chronograph for time measurement.
The first electric clocks had prominent pendulums because this was a familiar shape and design. Smaller clocks and watches with a spiral-balance are made on the same principles as pendulum clocks.
[edit]
Electric Clocks
Classification
There are actually four basic design classifications:
▪ Electromechanical clocks that use mechanics to rewind the mainspring (via attachment of a motor or an electromagnet)
▪ Electromechanical clocks that use mechanics to operate the pendulum or oscillator
▪ Electromagnetic clocks that use electromagnetic impulses to operate the pendulum or oscillator
▪ Synchronous clocks that rely on the the 50 or 60 Hz utility frequency of the AC power line as a timing source, by driving the clock gears with a synchronous motor.
[edit]
History
Electric Table Clocks With Large Numbers
In 1814, Sir Francis Ronalds (1788) of London invented the forerunner of an electric clock, the electrostatic clock. His prototype was powered with a dry pile battery. It proved unreliable in timekeeping, however, because of a strong dependence on a stable room temperature and 'weather conditions'.
In 1815, Giuseppe Zamboni (1776-1846) of Verona invented and showed another electrostatic clock run with dry pile battery and an oscillating orb. Over the test of time Zamboni's clock was praised 'the most elegant and at the same time the most simple movement yet produced by the electric column'.[1] Zamboni's clock had a vertical needle supported by a pivot and was so energy efficient that it could operate on one battery for over 50 years.
Numerous people were intent on inventing the electric clock with electromechanical and electromagnetic designs around the year 1840, such as Wheatstone, Steinheil, Hipp, Breguet, and Garnier, both in Europe and America.
In 1840, Alexander Bain (1811-1877), a Scottish clock and instrument maker is the first to invent and patent the electric clock. His original electric clock patent is dated October 10, 1840. On January 11, 1841, Alexander Bain along with John Barwise, a chronometer maker, took out another important patent describing a clock in which an electromagnetic pendulum and an electric current is employed to keep the clock going instead of springs or weights. Later patents expanded on his original ideas.
Matthias Hipp (1815-1893), clockmaker born in Germany, is credited with establishing the production series, mass marketable electric clock. Hipp opened a workshop in Reutlingen, Switzerland, where he developed an electric clock to have the Hipp-Toggle, presented in Berlin at an exhibition in 1843. The Hipp-Toggle is a device attached to a pendulum or balance wheel that electromechanically allows occasional impulse or drive to the pendulum or wheel as its amplitude of swing drops below a certain level, and is so efficient that it was subsequently used in electric clocks for over a hundred years. Hipp also invented a small motor and built the chronoscope and the registering chronograph for time measurement.
The first electric clocks had prominent pendulums because this was a familiar shape and design. Smaller clocks and watches with a spiral-balance are made on the same principles as pendulum clocks.
[edit]
Electromechanical Clock
[edit]
Description
The configuration of this device is comparatively very simple and reliable. The typical deviation of the electromechanical clock is about 10 seconds per hour and it usually can run for about a year using the energy of the single battery. The electrical current powers either a pendulum or an electromechanical oscillator.
The electromechanical oscillator component has an attached magnet that passes two inductors. When the magnet passes the first inductor or sensor, the simple amplifier opens the current across the second inductor, and the second inductor works as electromagnet, providing an energy pulse to the moving oscillator. This oscillator is responsible for the accuracy of the clock. The electronic part would not generate electrical pulses if the oscillator is absent or does not move. The resonance frequency of the mechanical oscillator should be about several times per second.
In the presented diagram of the 1968 year electromechanical clock, the resistor R1 can be about 27 kΩ, the capacitor C1 about 25 μF and capacitor C2 about 0,033 μF. Both inductors have about 2300 windings. The device is a common collector amplifier, opening current across the inductor Lu only when the oscillator magnet passes the sensor inductor L0, causing the base current and opening the transistor. This clock uses the 1.5 V battery (the most of devices used 1.5 - 4.5 V power source).
By the mid 19th century, ideas had already germinated for the first electrical clocks. The foreground was occupied less by the electrical drive of the clock itself, and much more by the control of several secondary clocks by a central timepiece. The section on 'Electrical horology systems' provides more on this.
The decorative, electrically driven clocks to be shown in this section appeared at the start of the 20th century. The first, really popular clock to be manufactured in large numbers and different versions was the English 'Eureka' with its impressive, large balance wheel. The system rests on the principle of a moving-coil instrument. The large balance wheel is also on ball bearings. It is the first known application of ball bearings in clocks.
Around 1910 the French 'Brillié' wall clock became common. This is actually a central timepiece which generates switching pulses for secondary clocks. The drive principle, however, has persisted almost to the present day, which is why this type of clock is also mentioned here. Unfortunately, little has been passed down of the history of Brillié clocks. The drive consists of a fixed electrical coil, inside which is a polarized magnet attached to the pendulum. A contact system controls the current in the coil in such a way that the pendulum receives a drive pulse in the right momentum. The motion work and other mechanisms are driven via a ratchet wheel.
The most common electrical Einzeluhr is the 'Bulle clock'. Despite its English name, this is a French make founded by Mr Favre-Bulle, watch and clock engineer from Besançon, in the years 1915 to 1920. The Bulle clock was manufactured and sold in many versions as a table or wall clock up to around 1970. The principle of the Bulle clock is similar to the Brillié, with the essential difference that the magnet is fixed and the coil is mounted on the pendulum. This arrangement is more complicated than the Brillié, but proved itself for more than 5 decades. Whether this arrangement was dictated by patent claims is beyond my knowledge. However, a Bulle clock runs for about 3 years with a modern 1.5V batterie (UM1)!
Electric Alarm Clocks With Large Numbers
Clock Numbers and Markers
It's easy to create your own custom dial using our press on numbers! Our adhesive backed numbers can be used on almost any smooth interior surface and will stick for years.
Hubcaps, record albums, cigar boxes, tiles or slate are all good examples of items around the house that you could easily make into an accurate quartz clock. As always, Clockparts.com is thinking quality first! Our adhesive numbers, our made in the USA and we believe they are best quality in the industry.
We carry both Arabic (regular) and Roman numbers in sets of all12 digits needed. Our number sizes range for ½' up to 4'. There is a lot of flexibility because of our wide selection of sizes.
Our adhesive backed numbers can be used with small clocks in the 3 inches or larger range, up to giant wall clocks that are 3 feet in diameter or more. It's all about selection and with our press on numbers you are able to create an unlimited number of amazing Clock Design
Desk Clocks With Large Numbers
Create the special clock of your dreams NOW using our press on numbers. If you need some creative inspiration, please feel free to email us or call our Technical Support department. We are always happy to help!
